CyberResearch STE 1xGTx Series User Manual Download Page 49

Page: 49 / 198

CyberResearch

Panel PCs

STE 1xGTx Series

Standard setup connects to devices with a standard parallel port, like printers

2.11 Gigabit Ethernet

The Broadcom BCM5787M PCI Express (PCIe) GbE controller is a 10/100/1000BASE-T

Ethernet LAN controller. The BCM5787M combines a triple-speed IEEE 802.3 compliant

Media Access Controller (MAC) with a triple-speed Ethernet transceiver, a PCIe bus

interface, and an on-chip buffer memory.

Figure 2-12: Ethernet

Some of the BCM5787 controller features are listed below:

Integrated 10/100/1000BASE-T transceiver

Automatic MDI crossover function

PCIe

v1.0a

10/100/1000BASE-T full/half-duplex MAC

Wake on LAN support meeting the ACPI requirements

Statistics for SNMP MIB II, Ethernet-like MIB, and Ethernet MIB (802.3z,

clause 30)

Serial EEPROM or serial flash support

JTAG

support

2.12 Front Panel

The front panel of the STE 1xGTx consists of an LCD monitor and a touch screen panel.

CyberResearch, Inc

25 Business Park Drive

P: (203) 643-5000; F: (203) 643-5001

Branford, CT USA

www.cyberresearch.com

Summary of Contents for STE 1xGTx Series























































































































































































Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands

CyberResearch STE 1xGTx Series, User Manual

Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands