CyberResearch STE 1xGTx Series User Manual Download Page 47

Page: 47 / 198

CyberResearch

Panel PCs

STE 1xGTx Series

Ethernet adapter cards

Modem

cards

Sound

cards

PCIe x4 cards available for the STE 1xGTx include:

Gigabit Ethernet adapter cards

SATA II / RAID controller cards

TV tuner cards

Graphics

cards

Firewire & USB cards

2.10 External Device Connectors

The external device connectors allow external components to be attached to the STE

1xGTx. The external communications device connectors are shown in the sections below.

2.10.1 USB 2.0 Ports

USB connections provide fast data transmission to external devices including USB flash

disks.

Figure 2-9: USB Ports

Some of the features of the USB ports include

USB 2.0 compliant

Support for low speed (1.5 Mb/s), full speed (12 Mb/s) and hi-speed

(480 Mb/s) USB devices

Hotplugging

capabilities

CyberResearch, Inc

25 Business Park Drive

P: (203) 643-5000; F: (203) 643-5001

Branford, CT USA

www.cyberresearch.com

Summary of Contents for STE 1xGTx Series























































































































































































Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands

CyberResearch STE 1xGTx Series, User Manual

Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands