CyberResearch STE 1xGTx Series User Manual Download Page 134

Page: 134 / 198

STE 1xGTx Series

CyberResearch

Panel PCs

Boot Display Device

Use the

Boot Display Device

option to select the display device used by the system

when it boots. Configuration options are listed below.

Auto

CRT - Default

LFP

CRT + LFP

Flat Panel Type [By Jumper]

Use the

Flat Panel Type

is set using the onboard jumper settings. The jumper settings

can be found in the Installation and Configuration chapter.

PID Current Jumper Setting [1-1024x768x24]

The

PID Current Jumper Setting

shows the current setting of the flat panel resolution

jumper.

Internal Graphics Mode Select [Enable, 8 MB]

Use the

Internal Graphic Mode Select

option to specify the amount of system memory

that can be used by the Internal graphics device.

Disable

Enable, 1 MB

1 MB of memory used by internal graphics device

Enable, 8 MB

EFAULT

8 MB of memory used by internal graphics device

Disabled

Scaling is disabled

116

CyberResearch, Inc.

Summary of Contents for STE 1xGTx Series























































































































































































Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands

CyberResearch STE 1xGTx Series, User Manual

Search results

Summary of Contents for STE 1xGTx Series

Reviews:

Related manuals for STE 1xGTx Series

Brands by name

Popular brands