manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 96 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 96

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

89

The file 0020f7123456.xml contains:

<?xml version="1.0" encoding="utf-8" ?>

<specific>

<MiscSettings>

<DeviceName>Newname</DeviceName>

<AutoprovFile>common.xml</AutoprovFile>

<AutoprovFile>sip_reg[macaddress].xml</AutoprovFile>

<AutoprovFile>audio[macaddress]</AutoprovFile>

<AutoprovFile>device.xml</AutoprovFile>

</MiscSettings>

</specific>

1. The device will first set it's name to 'Newname'.  

2. It will try to download http://example.com/common.xml.

3. It will try to download http://example.com/sip_reg0020f7123456.xml.

4. It will try to download http://example.com/audio0020f7123456.

5. It will try to download http://example.com/device.xml.

The device is reconfigured every time it downloads a new file so if two files configure the same 
option the last one will be the one that is saved.

It is possible to autoprovision autoprovisioning values (for example, to disable autoprovisioning or to 
configure a time to check for new files).

Checking for New 
Autoprovisioning 
Files after Boot

The device will always check for an autoprovisioning files on boot but it can be configured to also 
check after a periodic delay, when idle, or at a specified time. When one of these options is set, the 
device will download its autoprovisioning files again, and if it finds any differences from the files it 
downloaded on boot, it will force a reboot and reconfigure.

Summary of Contents for RAL 9003































































































































Reviews:

No comments