CyberData RAL 9003 Operation Manual Download Page 37

Page: 37 / 126

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

2.2.2.3 Singlewire InformaCast Talk-Back Speaker with Line Out

Figure 2-8

, for areas that require more speaker volume, the Singlewire InformaCast Talk-Back

Speaker can be connected directly to an auxiliary amplifier to drive additional horns or speakers.
This is done through the line-out connection.

Figure 2-8. Singlewire InformaCast Talk-Back Speaker with Line Out

AUX SPEAKER (-)
AUX SPEAKER (+)
GND
LINE OUT (-)
LINE OUT (+)
BUTTON LED (-)

BTN SENSE

BUTTON LED (+)

RELAY NO

RELAY COM

AUX POWER (-)

AUX POWER (+)

(+12VDC @ 1A)

J10

CLASS II WIRING

Office area in Factory

Factory Floor

Amplifier

Line Out:
Output Signal Amplitudes 2.0 VPP maximum
Output Level +2dBm nominal
Total Harmonic Distortion 0.5% maximum
Output Impedance 10k ohm

Speaker

Summary of Contents for RAL 9003































































































































Search results

Summary of Contents for RAL 9003

Reviews:

CyberData RAL 9003, Operation Manual, Page: 37 / 126

Search results

Summary of Contents for RAL 9003

Reviews: