manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 69 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 69

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

62

Slow Blink 

Strobe will blink ON at the specified brightness for one second then OFF 
for one second during the duration of the event.

Fast Blink 

Strobe will blink ON at the specified brightness then OFF five times per 
second during the duration of the event.

Nightringer Call Color 

Select desired color (only one may be chosen).

Red 

The red LED value for Nightringer.

Green 

The green LED value for Nightringer.

Blue 

The blue LED value for Nightringer.

Use this button to preview the strobe flashing behavior for the 

Nightringer 

Strobe Settings

.

RTP Settings

RTP Port (even) 

Specify the port number used for the RTP stream after establishing a SIP 
call. This port number must be an even number and defaults to 10500. 
The supported range is 0-65536. Enter up to 5 digits.

Jitter Buffer 

Specify the size of the jitter buffer (in milliseconds) used for SIP calls. Valid 
values are 50-1000.

Call Disconnection

Terminate Call After Delay 

Automatically terminate an active call after a given delay in seconds. A 
value of 0 will disable this function. Enter up to 8 digits.

Codec Selection

Force Selected Codec 

When configured, this option will allow you to force the device to negotiate 
for the selected codec. Otherwise, the device will perform codec 
negotiation using the default list of supported codecs.

Codec 

Select the desired codec (only one may be chosen).

Button Settings

Dial Out Extension 

Specify the extension the device will call when someone presses the Call 
button. Enter up to 64 alphanumeric characters.

Note

: For information about dial-out extension strings and DTMF tones, 

see 

Section 2.3.7.1, "Dial Out Extension Strings and DTMF Tones (using 

rfc2833)"

.

Extension ID 

A Caller identification string added to outbound calls. Enter up to 64 
alphanumeric characters.

Click the 

Save

 button to save your configuration settings.

Note

: You need to reboot for changes to take effect.

Click on the 

Reboot

 button to reboot the system.

Click on the 

Toggle Help 

button to see a short description of some of the 

web page items. First click on the 

Toggle Help 

button, and you will see a 

question mark (

) appear next to some of the web page items. Move the 

mouse pointer to hover over a question mark to see a short description of 
a specific web page item.

Table 2-13. SIP Configuration Parameters (continued)

Web Page Item

Description

Summary of Contents for RAL 9003































































































































Reviews:

No comments