manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 46 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 46

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

39

2.3.4 Log in to the Configuration Home Page

1. Open your browser to the Singlewire InformaCast Talk-Back Speaker IP address. 

Note

If the network does not have access to a DHCP server, the device will default to an IP 
address of 10.10.10.10.

Note

Make sure that the PC is on the same IP network as the Singlewire InformaCast Talk-Back 
Speaker.

Note

You may also download CyberData’s VoIP Discovery Utility program which allows you to 
easily find and configure the default web address of the CyberData VoIP products. 

CyberData’s VoIP Discovery Utility program is available at the following website address:

http://www.cyberdata.net/assets/common/discovery.zip

Note

The device ships in DHCP mode. To get to the 

Home

 page, use the discovery utility to scan 

for the device on the network and open your browser from there.

2. When prompted, use the following default 

Web Access Username

 and

 Web Access

 

Password

 to access the 

Home Page

 (

Figure 2-16

):

Web Access Username: 

admin

Web Access Password: 

admin

Summary of Contents for RAL 9003































































































































Reviews:

No comments