manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 22 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 22

 Product Overview

Starting a Push-to-Talk Session from a Singlewire InformaCast Talk-Back Speaker (Detailed)

Operations Guide

931260A

CyberData Corporation

15

1.9 Starting a Push-to-Talk Session from a Singlewire 
InformaCast Talk-Back Speaker (Detailed)

1.9.1 Optional 011185 Remote Call Button (sold separately)

Section 1.9, "Starting a Push-to-Talk Session from a Singlewire InformaCast Talk-Back Speaker 
(Detailed)"

 shows the optional 011185 Remote Call Button which is sold separately. For more 

information about this product, go to the following webpage:

http://www.cyberdata.net/voip/011185/

1.9.2 Procedure

To start a Push-to-Talk Session from a Singlewire InformaCast Talk-Back Speaker:

1. The person at the preconfigured Singlewire InformaCast Talk-Back Speaker must press the 

Remote Call Button. The speaker will immediately call a specific IP phone.

Figure 9. Press the Remote Call Button

Remote Call Button

Note

: See 

Section 

1.9.1, "Optional 011185 
Remote Call Button 
(sold separately)"

Summary of Contents for RAL 9003































































































































Reviews:

No comments