manualshive.com logo in svg

CyberData RAL 9003, Operation Manual, Page: 52 / 126

Share
Download
CyberData RAL 9003 Operation Manual Download Page 52

 

Installing the Singlewire InformaCast Talk-Back Speaker

Device Configuration

Operations Guide

931260A

CyberData Corporation

45

2. On the 

Device 

page, you may enter values for the parameters indicated in 

Table 2-7

.

Note

The question mark icon (

) in the following table shows which web page items will be defined 

after the 

Toggle Help

 button is pressed

.

Table 2-7. Device Configuration Parameters  

Web Page Item

Description

Volume Settings (0-9)

Disable Volume Control Dial 

Select this option to disable the volume control dial and enable digital 
volume control settings.

SIP Volume 

Set the speaker volume for a SIP call. A value of 0 will mute the speaker 
during SIP calls.

Multicast Volume 

Set the speaker volume for multicast audio streams. A value of 0 will 
mute the speaker during multicasts.

Ring Volume 

Set the ring volume for incoming calls. A value of 0 will mute the speaker 
instead of playing the ring tone when Auto-Answer Incoming Calls is 
disabled.

Sensor Volume 

Set the speaker volume for playing sensor activated audio. A value of 0 
will mute the speaker during sensor activated audio.

Push To Talk Volume 

Set the speaker volume for Push to Talk operation. A value of 0 will mute 
the speaker in Push to Talk mode.

Volume Boost: 

No Volume Boost

Volume Boost 1

Volume Boost 2

Volume Boost 3

Set the Boost level to increase the volume output of the speaker. Using 
Volume Boost may introduce audio clips or lessen the effectiveness of 
the echo canceler. Boost is only recommended for use with volumes set 
to level 9. 

Normal operation of the product can be met with volume levels 0 
through 9. 0 being mute and 9 being the loudest volume that in a normal 
arm's length and average background noise, will enable full duplex 
operation and give the best quality of sound output.

The volume boost options increase the output of the speaker by:

3db for Boost level 1

6db for Boost level 2

9db for Boost level 3

If the user would like a higher output from the speaker, the Boost 
settings are available. However, operation in 

Boost Mode

 may overdrive 

or clip the audio if, for example, the phone that is connected has a high 
microphone gain or if the person has a loud voice talking too close to the 
microphone.

The acoustic echo canceller also has a harder time maintaining full 
duplex operation when in the 

Boost Mode

. The product may drop from 

full duplex operation into half/duplex mode while in 

Boost Mode

.

Contact CyberData support for additional information if needed.

Summary of Contents for RAL 9003































































































































Reviews:

No comments