Custom Audio Electronics KPM216HII-ETH User Manual Download Page 31

Page: 31 / 112

4.4 Issuing

ticket

The printer allows you to choose between different operating modes for the issuance of printed tickets.
The operating modes shown in the following images, depend on the settings of the con

guration parameters and

commands sent to the printer.

NOTE:

For further information, refer to Chapter 5 and to the Commands Manual.

“PRESENT” MODE

The device starts the ticket printing

The ticket advances ahead to the ejector and is caught between the ejector rollers.

The printed part of ticket is collected while the device continues printing

Paper input

Printing head

Paper caught

between rollers

Ejector rollers

Paper input

4. OPERATION

User manual

KPM216HII ETH 31

Summary of Contents for KPM216HII-ETH

















































































































Search results

Summary of Contents for KPM216HII-ETH

Reviews:

Related manuals for KPM216HII-ETH

Brands by name

Popular brands

Custom Audio Electronics KPM216HII-ETH, User Manual

Search results

Summary of Contents for KPM216HII-ETH

Reviews:

Related manuals for KPM216HII-ETH

Brands by name

Popular brands