Culligan Premier Series Installation, Operation And Service Instructions Download

Page: 95 / 102

Optional Accessories

Cat. No. 01024000

Modem Connection

NOTE Use of the modem kit requires a one-year subscription to either a Level 1 or Level 2 Telecom package.

Self-service registration is available on CPort (www.cport.culligan.com) under the Technical Service

Tab on the Telemetry page’s subpage

Setup Self-Service

1. Before installing the modem into the back of the deionizer controller board, turn off the circuit board.
2. When handling all circuit boards, take care to only touch the edges of the circuit boards—not the metal pins.

The electronics on all circuit boards can be damaged by static electricity.

3. Make sure all of the pins at all four connectors are aligned between the modem board and the controller board.

Make sure that the modem board is fully seated into all four sockets.

4. When all connections have been made, restore power to the circuit board.

Installing a Modem on the Deionizer Circuit Board

Open the controller cover and locate the modem connection on the back of the board (see Figure 40). Insert the line

modem board (part number 01020307) into the socket on the back of the board. Make sure that all of the pins in all four

connectors are aligned, and make sure the modem is fully seated into all of the sockets.

Figure 40.

Modem location on back of the deionizer circuit board.

Programming the Modem on the Deionizer

SERVICE

FEB-01-13 12:11P

10.0GPM 161PPM

1. From the default home screen, press

to display the main menu.

>1)INFORMATION

2)MANUAL REGEN

3)SET DATE/TIME

4)ADV. SETUP

2. From the main menu screen, press

to 4) ADV. SETUP.

3. Press

. The screen displays the Advanced Setup menu.

Summary of Contents for Premier Series







































































































Search results

Summary of Contents for Premier Series

Reviews:

Related manuals for Premier Series

Brands by name

Popular brands

Culligan Premier Series, Installation, Operation And Service Instructions

Search results

Summary of Contents for Premier Series

Reviews:

Related manuals for Premier Series

Brands by name

Popular brands