CTE PIANOPLAN 600 J SPEEDY STANDARD Operator'S  Maintenance Manual Download Page 32

 

 

 

 

 

Operator’s and Maintenance Manual 
Pianoplan 600J Speedy Standard

 

 

 

 

CODE 

504196 

 

 

32 

7.

 

 INSTRUCTIONS TO CHARGE THE BATTERIES  

 

ATTENTION

:  it  is  obligatory  to  charge  the  batteries  after  each  use  of  the 

machine.  If  you  do  not  use  the  machine  for  a  long  time,  it  is,  in  any  case, 
necessary to charge the batteries every 14 days or 2 weeks.

 

It  is  prohibited  to  charge  the  batteries  with  a  battery  charger  with  a  different  voltage  or 
amperage other than that supplied by the manufacturer. 

The use of this machine is only 

allowed to duly instructed and trained personnel.   

Use an appropriate AC input tension as the one indicated on the battery charger. 
Use only batteries and battery chargers authorized by CTE. These instructions refer to the 
battery charger provided with the Pianoplan. 
Do not use  the battery charger if it is damaged or if you are not sure of its integrity and 
safety. 
If you use extensions leads, they must have plugs and sockets according to the law, suitable 
section cables to the voltage and the absorption of the battery charger. The extension must 

be taut. Put  the battery charger in a stable, dry and ventilated area. Pay attention  that the 
battery charger and the cables are not in contact with liquids or wet objects.

 

 

CHARGING the BATTERIES 
There  are  different  models  of  battery  charger.  For  the  one  provided  with  your 
machine, please follow the relative instructions. 

 

 

ATTENTION: be sure that the key switch of the Pianoplan 

(Fig. 4.2 

Pos.  4)

  is  on  the  "SWITCH  OFF"  position  and  that  the  red 

emergency button "emergency stop" 

(Fig. 4.2 Pos. 2)

 is pushed.

 

 

ATTENTION:  DO  NOT  USE  THE  PIANOPLAN  WITH  THE 
BATTERY CHARGER CONNECTED

 

We  advise  you  to  charge  the  Pianoplan  after  each  use.  Do  not  discharge  the 
batteries  to  exhaustion;  otherwise  it  is  necessary  to  use  an  alternative  battery 

charger to trickle charge it. 

 

 

ATTENTION

: the batteries installed on the machine are hermetic batteries 

and it is not necessary to overhaul them. 
For the battery recharge, please follow the following instructions.

 

 

 

 

 

 

Summary of Contents for PIANOPLAN 600 J SPEEDY STANDARD































































Reviews: