manualshive.com logo in svg

CSO A900, Instructions For Use Manual

Share
Download
CSO A900 Instructions For Use Manual Download Page 39

Z8A9F9 | IFU323EN00

 

 

INSTRUCTIONS FOR USE 

 

 

This document is the property of 

CSO Costruzione Strumenti Oftalmici srl. 

Any reproduction, even partial, it is prohibited.

 

37/60

 

Fluorescein semicircle too wide or too small. 

Image 

Cause 

Solution 

 

The image of the two 

semicircles is too wide. The 

intraocular pressure 

measurement might result 

higher than the real one. 

Carefully clean the measuring 

prism before positioning it 

again. 

 

The image of the two 

semicircles is too small. The 

intraocular pressure 

measurement might result 

lower than the real one. 

Carefully clean the measuring 

prism before positioning it 

again. 

 

The measuring prism does not touch the cornea or an excessive 

pressure has been applied. 

Image 

Cause 

Solution 

 

If the patient draws his/her 

head back slightly, irregular 

movements of the eye will 

happen. this will cause an 

unstable contact between 

measuring prism and eye. 

Ask the patient to stay perfectly 

still and open the eyes better. 

Repeat the measurement.  

 

 

 

Summary of Contents for A900

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands