background image

 

 

                                                                                                                                                     

SIGNATURE 2 SERIES 

                                                                                                                                         

WARNING

Lubricants

Do NOT use Vaseline, oils, hydrocarbon lubricants or spray silicone anywhere! Petroleum base lubricants will 
cause swelling of o-rings and seals. The use of other lubricants may attack plastic Noryl®. It is recommended 
that Dow Corning® silicone grease be used as a lubricant for all control valves. Dow Corning® 7 Release 
Compound is used in the manufacture of Chandler Systems control valves. (Part # LT-150)

Sealants

Pipe dope and liquid thread sealers may contain a carrier that attacks some plastic materials. It is recom-
mended that Teflon® tape be used to seal plastic Noryl® threaded fittings.

3

Hydroxr Specifications

-How The HYDROXR™ Works-

The HYDROXR™ consists of three components: HYDROXR™ Tank, Peroxide Feed System and Filter Tank. The 
first two items serve to oxidize and precipitate iron and sulfur so that they can later be removed by the filter. The water 
flows down through the mineral bed of the filter and out to the service lines. The collected precipitates must be regularly 
removed from the filter by reversing the flow through the filter and running to drain. Called 

Backwashing

 and lasting 10 

minutes, the process expands the mineral bed freeing the iron, sulfur and turbidity which is then washed out of the filter to 
the drain. It is important that the correct amount of water is available for the backwash cycle. Check pump capacity to be 
certain water is available in sufficient volume to adequately backwash the equipment at the specified rate. 
(See specifications.)

General 

Specifications

UTP15-S2

UTP20-S2

UTP25-S2

UTP30-S2

UTP40-S2

Filter Media Type

SmartBlend ™

Filter Media Capacity (cu ft)

1.5

2.0

2.5

3.0

4.0

Mineral Tank (Vortech ™)

10 x 54

12 x 52

13 x 54

14 x 65

16 x 65

Service Flow Rate - Continuous 
(gpm)

5

6

8

9

11

Service Flow Rate - Intermittent 
(gpm)

7

8

10

11

13

Backwash Flow Rate (gpm)

5.0

6.0

7.0

10.0

15.0

Gallons Used / Backwash

100

120

140

200

300

Space Required 

HydroxR ™ 

Tank

21 x 21 x 74

21 x 21 x 74

21 x 21 x 74

21 x 21 x 74

21 x 21 x 74

Space Required Filter Tank

10 x 10 x 62

12 x 12 x 60

13 x 13 x 62

14 x 14 x 73

16 x 16 x 74

Space Required Feed Pump System

17 x 17 x 28.5 17 x 17 x 28.5 17 x 17 x 28.5 17 x 17 x 28.5 17 x 17 x 28.5

Approximate Shipping Weight (lbs)

175

246

280

321

394

Summary of Contents for UTP15-S2





















Reviews: