background image

 

                                                                                                                

                       

 

            

SIGNATURE  2  SERIES                                                                                        

Installation

     

6

-Drain Line Connection-

1. Pull out clip and remove drain line assembly located on the left side of control valve. Remove drain line hose barb and    
    wrap threads with Teflon tape. Reinstall drain line hose barb. Caution: Hand tighten only!! Replace drain line assembly   
    and reinstall clip.
2. Install 1/2” I.D. line tubing (not included) from hose barb to an open drain. A 4” gap between the end of the drain line    
    and the open drain is required to prevent waste water backflow. Keep the drain line as short as possible. An overhead    
    drain line can be used if necessary but should discharge below the control valve. A syphon trap (taped loop)
    at the outlet of the drain line is advisable to keep the drain line full and assure correct flow during regeneration. Elbows       
    or other fittings must be kept at a bare minimum.

Note: 

Where the drain line is elevated above the control valve or exceeds 20’ in length, 3/4” I.D. drain line tubing should    

          be used.

-Potassium Permanganate Feed Rate-

The amount of potassium permanganate fed during regeneration is automatically controlled by the float assembly located 
inside the feed tank. This is an adjustable float, which must be set at a minimum of 4 1/4”, but not higher than 5 1/2”. This 
distance is measured between the bottom of chemical feed valve and the bottom of the float with the valve closed (float 
UP position). The float settings for each model are as follows:

  

Model 

#   Float 

Setting 

  Media 

Amount

 

 

IF-10-S2 

 

     

    4 1/4” 

 

 

     1.0 cu. ft.

 

 

IF-15S2  

 

     

    4 1/2” 

 

 

     1.5 cu. ft.

 

 

IF-20-S2 

 

     

  

 

 

IF-25-S2 

 

                 5 1/2” 

 

 

      2.0 cu. ft.

1. To measure and set the float, remove the chemical well cap and float assembly.
2. Remove rubber band from float valve.
3. Measure distance from bottom of chemical feed valve to the bottom of float with the float in the UP position. To move    
   float, slide rubber grommets up and down float shaft. Make certain both upper and lower grommets are 
   tightly against float body. Replace float assembly and chemical well cap.

WARNING: 

After adjustment, ensure that the float maintains proper up and down travel, otherwise, overfilling of the feed    

 

       tank could occur!

-Chemical Feed Line and Overflow Connections-

1. Position Potassium Permanganate Tank (KMNO4) on a smooth, level surface near the filter media tank. If necessary,    
    the KMNO4 tank can be placed at a higher level than the resin tank, but never at a lower level.
2. Install one end of 3/8” O.D. by 1/4” I.D. chemical line tubing (included with unit) to compression fitting located on right    
    side of control valve, behind backplate.
3. Remove KMNO4 tank cover.
4. Insert opposite end of chemical line through outer hole in KMNO4 tank.
5. Connect chemical line to compression fitting on float valve located on top of chemical well.
6. Install 1/2” I.D. drain line tubing (not included) to the overflow fitting on KMNO4 tank located just below the chemical  

 

    line.
7. Run the opposite end of KMNO4 tank drain line to a suitable drain.

Note:

 The KMNO4 tank drain is gravity flow and must discharge below the overflow fitting.

Caution: 

Do not tee to the main drain line from control valve.

NOTICE: 

The KMNO4 overflow is provided as a back-up in the event the float shut-off should fail, allowing the KMNO4 

tank to overfill. This drain connection would then carry the excess chemical to the drain and prevent flooding of the floor, 
which could be hazardous to health or damage furniture or carpets. Therefore, no liability will or can be assumed by the 
manufacturer of the filter should this occur.

Summary of Contents for greensand plus IF10-S2

























Reviews: