background image

 

1

 

INTRODUCTION 

The CS-47 is a cellular backup to PSTN phone line system. 

When connected to an alarm control panel, the CS-47 operates as a GSM 

back up unit to a PSTN line, enabling to re-direct incoming and outgoing 

calls to the GSM network in case of regular phone line failure. 

1.1  General Specification: 

  Built-in Tri-Band GSM transceiver 

  Continuous PSTN line supervision 

  GSM backup at PSTN Line failure 

  Programmable SMS messages  

  Multi language support for SMS and for PC graphical interface  

  4 inputs for SMS and output operation  

  4 outputs operated either locally or by SMS 

  Battery backup support including charger 

  Status report by SMS messages 

  Cheaper call routing to GSM when dialing to a cellular number 

1.2  Basic Functionality 

The Mobile Bridge provides operators the means to connect to various 

inputs and output devices. It uses cellular technology to send and receive 

messages, allowing operators to monitor and control the required devices. 

For example, the Mobile Bridge sends an SMS to the security center if an 

office has been ente red without authorization. 

1.3  Reduction of Costs  

With the CS-47, all telephone landlines (PSTN) are routed through the 

CS-47 unit, together with the cellular modem that is connected to the CS-

47. Certain telephone calls are then routed through the CS-47 modem. This 

reduces costs on these telephone calls, because the System automatically 

selects the least expensive route and diverts calls to either the landline or 

the cellular line, as relevant. The switch is according to a programmable 

prefix number, when the unit detects this prefix number that was 

programmed it switches the call to the cellular line although a PSTN line is 

connected. 

Summary of Contents for CS-47 GSM





















Reviews: