manualshive.com logo in svg

Crestron TSW-570P, Product Manual

Share
Download
Crestron TSW-570P Product Manual Download Page 159

Product Manual — Doc. 8550E

TSW-70 Series • 153

Wi-Fi Setup

Tap Wi-Fi Setup on the Setup screen to display the Wi-Fi Setup screen. (TSW-770 and
TSW-1070 only)

Wi-Fi Setup Screen

Use the Wi-Fi Setup screen to view the Wi-Fi network MAC and IP addresses, subnet mask
address, default router address, primary and secondary DNS addresses, hostname, domain, and
various details about the Wi-Fi connection. A Link indicator is provided to indicate the status of
the Wi-Fi connection. (Green indicates that the Wi-Fi connection is active.)

NOTE: 

Ethernet must be disabled before a Wi-Fi connection can be configured.

The following buttons are provided for configuring Wi-Fi settings:

l

Tap On or Off under Wi-Fi Access to turn the Wi-Fi adapter on or off. If Wi-Fi Access is set
to Off, Wi-Fi will not function and an Ethernet connection can be established.

l

Tap On or Off under DHCP Enable to turn DHCP (dynamic host configuration protocol) on
or off.

NOTE:

DHCP is enabled on the touch screen by default.

l

If DHCP is turned off, tap Set Static IP Address Settings to enter static IP addresses
manually.

l

Tap Set Hostname to enter a new touch screen hostname using an on-screen keyboard.

l

Tap APPLY CHANGES to apply any new Wi-Fi settings to the touch screen and to stay in
setup mode.

l

Tap REBOOT to exit setup mode and reboot the touch screen.

Summary of Contents for TSW-570P



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands