Home
/
Crestron
/
TSW-570P
/
Product Manual

Crestron TSW-570P, Product Manual

Share

Page: 116 / 226

Crestron TSW-570P Product Manual Download Page 116

110 • TSW-70 Series

Product Manual — Doc. 8550E

Connect the Touch Screen

Route all necessary cables through the rear of the mounting bracket, and then make connections
to the bottom of the touch screen rear housing.

Observe the following when connecting the touch screen:

l

Power and data connection is provided to the touch screen by a single Ethernet cable. A
Crestron PoE (Power over Ethernet) power supply, such as the

, or a PoE-

capable network switch is recommended (neither included).

l

The USB ports are used to connect compatible Crestron LED accessories to the touch
screen.

l

Apply power after all connections have been made.

Mount the Touch Screen

After all connections have been made, push the touch screen gently into the mounting bracket so
that its rear housing is secured within the center opening of the mounting bracket.

If the touch screen is not level after installation, pull it out of the mounting bracket and loosen
the screws holding the bracket into place. This procedure allows the mounting bracket to be
rotated slightly.

Once the mounting bracket has been repositioned, retighten the screws, reinstall the touch
screen into the bracket, and ensure that the touch screen is now level.

«
...
114
115
116
117
118
...
»

Summary of Contents for TSW-570P



































































































































































































































Reviews:

No comments

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands