manualshive.com logo in svg

Crestron TSW-570P, Product Manual

Share
Download
Crestron TSW-570P Product Manual Download Page 135

Product Manual — Doc. 8550E

TSW-70 Series • 129

Access the Device Setup Screens

To access the built-in setup screens, place five fingers on the display and hold for 15 seconds. The
main Setup screen is displayed (TSW-570 shown).

Use the setup screens to configure various settings for the touch screen, including Ethernet
setup, IP table setup, audio setup, display setup, standby timeout,and diagnostics.

NOTE: 

Time zone settings do not need to be configured on the touch screen, as these settings

will be pushed to the touch screen from the control system running Crestron Home.

Access the Web Configuration Interface

The touch screen provides a web configuration interface that is used to view and configure
various touch screen settings. The interface can be accessed using the touch screen IP address.

To access the web configuration interface using the touch screen IP address:

1. Ensure that the touch screen is connected to the network.

2. Use the Device Discovery tool in Crestron Toolbox™ software to discover the touch screen

and its IP address on the network.

3. Enter the touch screen IP address into a web browser.

Summary of Contents for TSW-570P



































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands