Crestron TSW-570P Product Manual Download Page 146

Page: 146 / 226

140 • TSW-70 Series

Product Manual — Doc. 8550E

Local Configuration

Refer to the following sections for information about configuring the device locally using its
built-in setup screens.

Access the Setup Screens

The setup screens enable basic configuration prior to regular operation of the touch screen.

NOTE:

The TSW-570P 5 in. portrait touch screen provides the same setup screens that are

described in this topic, but the appearance and layout of the screens have been modified for
portrait orientation.

To access the touch screen's built-in setup screens during regular operation, place five fingers on
the display and hold for 15 seconds.

The main Setup screen is displayed (TSW-1070 shown).

TSW-1070 Setup Screen

The Setup screen shows the IP address and hostname of the touch screen and provides the
following configuration selections:

Buttons for Ethernet setup, IP table setup, audio setup, display setup, standby timeouts,
application selection, Wi-Fi® network setup, diagnostics, Bluetooth® beacon configuration,
and the virtual toolbar (model dependent).

A button to toggle system messages on or off

An About button that provides information about the touch screen.

Summary of Contents for TSW-570P



































































































































































































































Search results

Summary of Contents for TSW-570P

Reviews:

Brands by name

Popular brands

Crestron TSW-570P, Product Manual

Search results

Summary of Contents for TSW-570P

Reviews:

Brands by name

Popular brands