background image

Appendix E—Crankcase Assembly Details

Ref 

No. Part No.

Description

1.

1737

Bearing cone

2.

3638

Spacer

3.

3635

Drive sprocket

4.

1284

Crankshaft orifice

5.

2135

Drive pin

6.

2933

Link pin

7.

3786

Crankshaft

8.

3503

Flywheel key

9.

3580

Bearing cone

10. 3786-X1

Crankshaft assembly

11. 7001-031NC075A

Bolt (5/16 - 18 x 3/4" hex head)

12. 2122

Inspection cover

13. 2123

Gasket, inspection cover

14. 2-112Ac

O-ring

15. 3225-X1

Oil bayonet assembly (w/O-ring)

16. 2126

Breather ball

17.

3579

Bearing cup

18.

3589

Bearing adjustment shim (.005")

3589-1

Bearing adjustment shim (.007")

3589-2

Bearing adjustment shim (.020")

19. 3539

Bearing cover

20. 3526

Oil seal

21. 1280

Filter screw

22. 1281

Gasket, filter

23. 2-116Ac

O-ring

24. 1276

Washer

25. 1275

Oil filter screen

26. 3443

Pipe plug (1/2" NPT steel)

27. 3221

Crankcase

28. 7001-037NC100A

Bolt (3/8 - 16 x 1" hex head Gr. 5)

29. 3875

Access cover

30. 7003-025NC037E

Screw (1/4 - 20 x 3/8")

31. 3874

Gasket (access cover)

32. 1515-X

Closure cap assembly

33. 7001-025NC050A

Bolt (1/4 - 20 x 1/2" hex head)

34. 1515

Closure cap

35. 1516

Closure body

36. 2-118Ac

O-ring

37. 1290

Relief valve adjusting screw

38. 2-011Ac

O-ring

39. 1291

Adjusting screw locknut

40. 1292

Relief valve spring

41. 1293

Relief valve ball

42. 4222-Xb

Oil filter adapter assembly (w/pin)

43. 2-228Ac

O-ring

44. 2849-1Xb

Oil pump assembly

45. 2851

Spring guide

46. 2852

Oil pump spring

47. 3219

Pump shaft adapter

Crankcase Assembly Bill of Materials

Assembly 

Number

Assembly Name

3221-X1

Crankcase assembly (M, 4, 8, 9) without lubricator

3221-X2

Crankcase assembly (M7, 78) without lubricator 

3221-X3

Crankcase assembly (L, 4, 8, 9) with lubricator

3221-X4

Crankcase assembly (L7, 78) with lubricator

Must be rebored and honed after replacing (0.876"/0.875" diameter)

Caution: To avoid damage during assembly, refer to installation 
Instruction Manual IE400.

See O-ring chart above for details.

 

 

WARNING

Always relieve pressure in the unit before attempting any 
repairs.

Ref 

No. Part No.

Description

48. 2-112Ac

O-ring

49. 2805-Xa

Pump shaft bushing

50. 1629

Pipe plug (1/16 NPT fl. seal)

51. 1736

Bearing cup

52. 1302

Oil pressure gauge

53. 1044

Bushing (1/8 x 1/4 NPT)

54. 3220-2

Bearing carrier

55. 3289

Pipe plug (1/4 NPT fl. seal)

56. 2131

Bearing carrier gasket

57. 2961-X

Air release valve assembly

58. 2590

Pipe plug (1/8 NPT fl. seal)

59. 4225

Filter

60. 2798

Pump cover pin (included w/4222-X)

61. 3220-2X

Bearing carrier assembly

62. 4222

Oil filter adapter

63. 3289

Pipe plug (1/4" x 18 NPTF x 7/8")

O-ring Code

A

Buna-N

37

Summary of Contents for WFD551









































Reviews: