background image

Never use gasoline or other inflammable gas near the air-conditioner, which is very 
dangerous. 
When the air conditioner operation

 

is abnormal, such as burnt smell, deformation, fire

smoke, and so on, it is forbidden to continue using

 

the air conditioner, the main power 

switch of the air conditioner must be cut off immediately and the agent must be 
contacted.  

Do not turn the air-conditioner on and off from the main power switch. Use the 
ON/OFF operation button.    

 

Do not stick anything into the air inlet and air outlet of both the indoor and outdoor 
units. This is dangerous because the fan is rotating at a high speed. 
Do not cool or heat the room too much if babies or invalids are present.
Do not turn the air-conditioner on and off from the main power switch. Use the 
ON/OFF operation button.    

 

Details of type and rating of circuit breakers / ELB is detailed in outdoor instruction
manual.  
The method of connection of the appliance to the electrical supply and interconnection 
of separate components is detailed in below part.  
The wiring diagram with a clear indication of the connections and wiring to external 
control devices and supply cord is detailed in below part. The cord of the H07RN-F 
type or the electrically equivalent type must be used  for power connection and 
interconnection between outdoor unit and indoor unit. The size of the cord is detailed 
in below part.  
The information of dimensions of the space necessary for correct installation of the 
appliance  including the minimum permissible distances to adjacent structures is 
detailed in below part.  
The range of external static pressures for ducted appliances is detailed in below part.  

2

WARNING

CAUTION

NOTE

:

                           

Storage condition:    Temperature -25~60

                                         Humidity      30%~80%

The numbers in the model represent the cooling capacity in 

W

/100

DC Inverter E

-

Series 

Duct Type

 Unit 

Summary of Contents for CH-ID0100RKE























Reviews: