Contec CNT24-2GY User Manual Download Page 55

Page: 55 / 73

5. Troubleshooting

CNT24-2(USB)GY

Uninstall procedure for XP and Server 2003, use [My Computer] - [Control Panel] -

[Add and Remove Programs] to uninstall the development environment.

Uninstall procedure for Windows Me

< Uninstalling the device driver >

Use [My Computer] - [Control Panel] - [Add or Remove Programs] to uninstall the

device driver.

Select [CONTEC API-***(WDM) driver] and then click [Change/Remove].

"***" contains the driver category name (caio, ccnt, cdio, csmc, etc.).

< Uninstall the development environment >

Use [My Computer] - [Control Panel] - [Add or Remove Programs] to uninstall the

development environment.

Select [CONTEC API-***(WDM) VerX.XX (development environment)] and then

click [Change/Remove].

"***" contains the driver category name (AIO, CNT, DIO, SMC, etc.).

Uninstall procedure for Windows 98, 98SecondEdition

< Uninstalling the device driver >

Use [My Computer] - [Control Panel] - [Add or Remove Programs] to uninstall the

device driver.

Select [CONTEC API-***(WDM) driver] and then click [Change/Remove].

"***" contains the driver category name (caio, ccnt, cdio, csmc, etc.).

< Uninstall the development environment >

Use [My Computer] - [Control Panel] - [Add or Remove Programs] to uninstall the

development environment.

Select [CONTEC API-***(WDM) VerX.XX (development environment)] and then

click [Change/Remove].

"***" contains the driver category name (AIO, CNT, DIO, SMC, etc.).

CAUTION

Summary of Contents for CNT24-2GY










































































Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands

Contec CNT24-2GY, User Manual

Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands