Contec CNT24-2GY User Manual Download Page 13

Page: 13 / 73

1. Introduction

CNT24-2(USB)GY

Customer Support

CONTEC provides the following support services for you to use CONTEC products

more efficiently and comfortably.

Web Site

https://www.contec.com/

The latest product information

Up-to-date information of the product is supplied.

In addition, the product manual with the form of PDF file and various technical data

are supplied.

Free download

You can download the up-to-date driver and missing files.

In addition, you can also download sample programs in various languages.

Limited One-Year Warranty

CONTEC product is warranted by CONTEC CO., LTD.. to be free from defects in

material and workmanship for up to one year from the date of purchase by the original

purchaser.

Repair will be free of charge only when this device is returned freight prepaid with a

copy of the original invoice and a Return Merchandise Authorization to the distributor

or the CONTEC group office, from which it was purchased.

This warranty is not applicable for scratches or normal wear, but only for the

electronic circuitry and original boards. The warranty is not applicable if the device

has been tampered with or damaged through abuse, mistreatment, neglect, or

unreasonable use, or if the original invoice is not included, in which case repairs will

be considered beyond the warranty policy.

Summary of Contents for CNT24-2GY










































































Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands

Contec CNT24-2GY, User Manual

Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands