manualshive.com logo in svg

Contec CNT24-2GY, User Manual

Share
Download
Contec CNT24-2GY User Manual Download Page 34

 

3. Setup 

 

 

 

CNT24-2(USB)GY 

27 

Point 

    By the setting above, Phase-A and Phase-Z rise is detected within the module.   

First, check out phase-Z rise, clear the counter data at the next rise of phase-A.  
Even if the phase-Z input turns LOW before phase-A rises, the counter data will be 
cleared. 

Setting the method of clearing 

Phase-Z can also be set enabled/disabled besides the logic setting.   

There are 3 methods of setting as follows: 

(1) 

Phase-Z input disabled 

(2) 

After the method of clearing is set to “one time” by using CntSetZMode(), the 

next phase-Z input is effective. 

(3)

 

Enabled for all phase-Z input 

Points 

- The initial setting is “Enabled for one time”. 

- When “Enabled for one time” is set, use CntStopCount() stop counting.    If execute 

CntStartCount() again, the “Phase-Z effective one time” setting is effective. 

- When phase-Z/CLR input is not used, please set to “Phase-Z input Disabled”. 

Summary of Contents for CNT24-2GY










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands