manualshive.com logo in svg

Contec CNT24-2GY, User Manual

Share
Download
Contec CNT24-2GY User Manual Download Page 14

 

1. Introduction 

 

 

 

CNT24-2(USB)GY 

7 

How to Obtain Service 

For replacement or repair, return the device freight prepaid, with a copy of the original 

invoice.    Please obtain a Return Merchandise Authorization Number (RMA) from the 

CONTEC group office where you purchased before returning any product. 

*  No product will be accepted by CONTEC group without the RMA number. 

Liability 

The obligation of the warrantor is solely to repair or replace the product.    In no event 

will the warrantor be liable for any incidental or consequential damages due to such 

defect or consequences that arise from inexperienced usage, misuse, or malfunction of 

this device. 

Safety Precautions 

Understand the following definitions and precautions to use the product safely. 

Safety Information 

This document provides safety information using the following symbols to prevent 

accidents resulting in injury or death and the destruction of equipment and resources.   

Understand the meanings of these labels to operate the equipment safely. 

 

DANGER indicates an imminently hazardous situation 

which, if not avoided, will result in death or serious injury. 

 

WARNING indicates a potentially hazardous situation 

which, if not avoided, could result in death or serious injury. 

 

CAUTION indicates a potentially hazardous situation 

which, if not avoided, may result in minor or moderate 

injury or in property damage. 

 

DANGER

WARNING

CAUTION

Summary of Contents for CNT24-2GY










































































Reviews:

No comments

Brands by name

Popular brands

Load more brands