Contec CNT24-2GY User Manual Download Page 21

Page: 21 / 73

3. Setup

CNT24-2(USB)GY

Setup Flow

The following shows the basic flow for installing module.

Software Installation

Install software.

Illustration of Menu Screen

Points

- Please set up the supplied disk if it has not been set up. The menu starts

automatically.

- If the menu do not start, launch X: AUTORUN.EXE(X: disk drive) from [Run…] in

Start menu.

- The screen design may be different.

Connecting to a PC
-Installing USB driver

Setting Properties
Using Device Manager
-Setting device name

Software Installation
-API-USBP(WDM)
Development
Environment
-Utilities

Page 14

Page 16

Page 18

Install the Development
Environment such as sample
programs and online help, etc.

Install the utility.

Refer to the user’s guide.
Refer to the description about
disk.

Install the C-LOGGER.
*Cannot be used for this product.

Summary of Contents for CNT24-2GY










































































Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands

Contec CNT24-2GY, User Manual

Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands