Contec CNT24-2GY User Manual Download Page 25

Page: 25 / 73

3. Setup

CNT24-2(USB)GY

Setting Properties Using Device Manager

After connecting module with a PC and completing driver installation, open device

manager and set properties.

Step1 Starting Device Manager

Right-click on [My Computer] and select

[Properties] to start device manager.

[XXXXX] within CONTEC Devices

expresses the name from getting rid of GY

from the model of module.

In the case of Windows XP/2000

From [Start] menu, click on [Settings]-[Control Panel]-[System] and then click on

[Device Manager] button in [Hardware] tab.

Step2 Setting the Device Name

Right-clicking on module name and selecting

[Properties] displays [Module Properties].

Open [Common Settings] tab and enter arbitrary

name in the editing box for device name.

(Default name also can be used.)

[XXXXX] will appear as CNT000

USB driver can not be used without settings. Settings must be performed.

CAUTION

Summary of Contents for CNT24-2GY










































































Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands

Contec CNT24-2GY, User Manual

Search results

Summary of Contents for CNT24-2GY

Reviews:

Brands by name

Popular brands