background image

7

 

 

Water damage

 

 

 To prevent flooding due to leakage, the installation room must be equipped with a floor drain 

and/or a leakage monitor with a corresponding alarm.

 

Electric shock

 

 

Work on the electrical supply may only be carried out by a qualified electrician.

 

 

 Check the system’s electrical equipment on a regular basis. Any loose connections 

or scorched cables must be removed immediately.

 

 

 The control cabinet must be kept locked at all times. Access is only granted  

to authorized personnel.

 

 

 If work needs to be carried out on live parts, a second person must be called in  

so that they can switch off the main switch as necessary.

 

 

Do not touch the electrical components with wet hands.

 

 

 Disconnect the system from the power supply before working on electrical system parts.

 

Mechanical/hydraulic energy

 

 

Some system parts are under overpressure of up to 25 bar.

 

 

The system must be de-pressurised before repair or maintenance work is carried out.

 

Hygienically critical applications

 

 

 There is a risk of contamination of system components if the system has not been  

adequately preserved. The preservation instructions must be observed.

 

 Faults which could impair safety must be rectified immediately. This is ensured by the operator 

himself or an operator-commissioned company.

 

1.7  

 Hazard-preventing protective devices  

and safety measures

1.7.1 

Protective devices

 

 

 Before switching on the system, all protective devices must be properly fitted and checked  

to ensure they are in working order.

 

 

 Protective devices may only be removed after the machine has been switched  

off and secured against being switched back on.

 

 

 The required personal protective equipment for the operating personnel must be provided  

by the operator and worn by the operating personnel when they are working on the system.

 

 

 All existing protective devices must be checked regularly by the operator or an  

operator-commissioned company.

1.7.2  

Informal safety measures

 

 

The operating instructions must be kept at the usage location permanently.

 

 

 In addition to the operating instructions, the generally applicable and local regulations 

for accident prevention and environmental protection must be provided and observed.

 

 

 All safety and hazard notices on the system as well as the labelling of the operating 

and control elements must be kept in legible condition.

General safety instructions

Summary of Contents for CONDAIR SOFT

























































Reviews: