Compaq ProLiant DL580 Setup And Installation Manual Download Page 154 | Manualshive

Page: 154 / 222

background image

A-2

Compaq ProLiant DL580 Server Setup and Installation Guide

Compaq Confidential – Need to Know Required

Writer:

Cynthia Dresden

Project:

Compaq ProLiant DL580 Server Setup and Installation Guide

Comments:

Part Number:

159213-003

File Name:

i-appa Regulatory Compliance Notices.doc

Last Saved On:

4/5/01 2:35 PM

Federal Communications Commission
Notice

Part 15 of the Federal Communications Commission (FCC) Rules and
Regulations has established Radio Frequency (RF) emission limits to provide
an interference-free radio frequency spectrum. Many electronic devices,
including computers, generate RF energy incidental to their intended function
and are, therefore, covered by these rules. These rules place computers and
related peripheral devices into two classes, A and B, depending upon their
intended installation. Class A devices are those that may reasonably be
expected to be installed in a business or commercial environment. Class B
devices, including personal computers, are those that may reasonably be
expected to be installed in a residential environment. The FCC requires
devices in both classes to bear a label indicating the interference potential of
the device as well as additional operating instructions for the user.

The rating label on the device shows which class (A or B) the equipment falls
into. Class B devices have an FCC logo or FCC ID on the label. Class A
devices do not have an FCC logo or FCC ID on the label. Once the class of the
device is determined, see the following corresponding statement.

Class A Equipment

This equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference, in which case the user will be required to
correct the interference at personal expense.

«
...
152
153
154
155
156
...
»

Summary of Contents for ProLiant DL580































































































































































































































Reviews:

No comments

Related manuals for ProLiant DL580

Brand: Acer Pages: 4

Aspire Z5600 Series

Brand: Acer Pages: 11

Brand: Acer Pages: 17

Brand: Acer Pages: 7

Brand: EAI Pages: 132

Brand: Avalue Technology Pages: 15

Brand: Fluidwell Pages: 52

Brand: Gateway Pages: 108

Brand: EUROCOM Pages: 176

Brand: AXIOMTEK Pages: 64

Brand: Advantech Pages: 44

Brand: Aaeon Pages: 44

Power Panel 300

Brand: B&R Industries Pages: 612

Brand: Gateway Pages: 346

Brand: Vivo Pages: 5

SIMATIC VPU200-3104

Brand: Siemens Pages: 28

SIMATIC Rack PC IL 40

Brand: Siemens Pages: 40

SIMATIC PC BI10

Brand: Siemens Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands