manualshive.com logo in svg

Compaq AA-RHBYA-TE 135267-001, User Manual

Share
Download
Compaq AA-RHBYA-TE 135267-001 User Manual Download Page 217

Telnet Commands  

B-71

spinSilk nMillions

 where 

nMillions

 is the number of frames for

the test to execute expressed as millions of frames. If you do not include the
nMillions parameter, the spinSilk test runs until <return> is pressed.

admin> spinSilk 5

Running Spin Silk .............
One moment please ...
Transmitting ... done.
Spinning ...
port  0 Rx/Tx 1 of 5 million frames.
port  1 Rx/Tx 1 of 5 million frames.
port  0 Rx/Tx 2 of 5 million frames.
port  1 Rx/Tx 2 of 5 million frames.
port  0 Rx/Tx 3 of 5 million frames.
port  1 Rx/Tx 3 of 5 million frames.
port  0 Rx/Tx 4 of 5 million frames.
port  1 Rx/Tx 4 of 5 million frames.
port  0 Rx/Tx 5 of 5 million frames.
port  1 Rx/Tx 5 of 5 million frames.

Diagnostics Status:  Thu Jul 30 14:43:36 1998

port#:   0   1  16
diags:  OK  OK  OK
state:  UP  UP  UP

 st0:   5022504 frTx  5003329 frRx  0  LLI_errs  <looped-1>
 st1:   5003616 frTx  5022790 frRx  0  LLI_errs  <looped-0>
 st16:        0 frTx        0 frRx  0  LLI_errs.

Central Memory OK
Total Diag Frames Tx: 48
Total Diag Frames Rx: 0

value = 0 = 0x0

Figure B-48.  spinSilk Command Example 2

Summary of Contents for AA-RHBYA-TE 135267-001

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands