manualshive.com logo in svg

Compaq AA-RHBYA-TE 135267-001, User Manual

Share
Download
Compaq AA-RHBYA-TE 135267-001 User Manual Download Page 194

B-48

   StorageWorks Fibre Channel Storage Switch User's Guide

Table B-10
portShow Command Field Descriptions 

continued

Type

Field

Description

Suspended

Number of suspended interrupts

Parity_err

Number of parity errors.

Error Statistics

Link_failure

Number of link failures.

Loss_of_sync

Loss of synchronization.

Loss_of_sig

Loss of signal (no light).

Protocol_err

Protocol error.

Invalid_word

Invalid word (encoding errors
inside of frames).

Invalid_crc

Invalid CRC in a frame.

Delim_err

Delimeter error (order set)

Address_err

Address id error (S_ID D_ID)

Lr_in

Link reset in (primitive
sequence). Does not apply to
FL_Port.

Lr_out

Link reset out (primitive
sequence). Does not apply to
FL_Port.

Ols_in

Offline resent in (primitive
sequence). Does not apply to
FL_Port.

Ols_out

Offline resent in (primitive
sequence). Does not apply to
FL_Port.

Frjt

Number of frames rejected.

Fbsy

Number of frames busy.

Summary of Contents for AA-RHBYA-TE 135267-001

































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands