Configuration via Web Interface
Commend SIP Series
46
2.0/0612
Audio In/Out
In the section
Audio
In/Out
the configuration of the audio output and audio feed-in is carried out:
Internal Loudspeaker:
If the checkbox is activated, the audio signal is put out via the internal loud-
speaker.
Line out:
If the checkbox is activated, the audio signal is put out via the terminals “Line+” and
“Line–” (connection possibility for an external loudspeaker
see page 29
).
Handset Loudspeaker(EP):
If this checkbox is activated, then the audio signal is put out via the
terminals “EP+” und “EP–”, i.e. via the loudspeaker of the handset/headset (
see page 29
).
Handset Loudspeaker(EP) overrides Audio Out:
If this checkbox is activated, then the audio si-
gnal is put out only via the terminals “EP+” and “EP–” as soon as a handset/headset is connected
(even if
Handset Loudspeaker(EP)
is not activated). This also means, even if
Internal Loud-
speaker
and
Line out
are activated, the audio signal will only be put out at the connected handset/
headset.
Internal Microphone:
If the option field is activated, audio is fed-in only via the internal micro-
phone (i.e. terminals “EM+” and “EM–” for microphone of the handset/headset are deactivated).
Handset Microphone (EM):
If the option field is activated, audio is fed-in only via the terminals
“EM+” and “EM–”, i.e. via the microphone of the handset/headset (the internal microphone is deac-
tivated).
Handset Microphone (EM) overrides Audio in:
If the checkbox is activated, then the audio signal
is fed-in only via the terminals “EM+” and “EM–” as soon as a handset/headset is connected (even
if
Handset Microphone(EM)
is not activated). This also means, even if
Internal Microphone
and
is activated, the audio signal will only be fed-in via the microphone of the connected handset/head-
set.
Handset Microphone (EM) overrides Audio In and Out:
This checkbox is required for the hand-
set/headset, which can be detected (by the respective SIP device) via the microphone input only, like
the handset
WSSH 50P
.
I.e. if the audio signal shall be put out only via the terminals “EP+” and “EP–” when using a
WSSH 50P (as described at
Handset Loudspeaker(EP) overrides Audio Out
above
), then this
checkbox has to be activated. Additionally to that, audio will be fed-in via the terminals “EM+” and
“EM–” as described at
Handset Microphone (EM) overrides Audio In
above
.
Pre-Recorded Audio
In this section, audio files (pre-recorded audio) can be loaded into the memory of the SIP station:
Attention:
For changing the default values of the microphone sensitivity / volume level (in particular for conver-
sations between 2 SIP stations), in combination with changes of the values for the noise and echo
suppression, the information regarding audio configuration on
page 62
shall be read previously.
Attention:
This function is not available for the
SIP Series M
.
The terminals “Line +” and “Line –” function for devices of the SIP Series M as “
Line In
”. I.e. the ter-
minals can be used for
feed-in
of
audio
(e.g. music, radio conference).
Attention:
This function is not available for the handset
WSSH 50P
. If the audio signal shall be put out via the
loudspeaker of the handset WSSH 50P – as soon as the handset is connected – then the checkbox
Handset Microphone (EM) overrides Audio In and Out
has to be activated
see below
.
This also applies to handsets/headsets. which can
only
be
detected
via the
microphone input
.
Memory:
max. 60 seconds
Audio format:
Accepted:
WAV / 8– 48 kHz
8, 16 bit / mono,stereo
Recommended:
WAV / min. 16 kHz
16 bit / mono
Attention:
One single WAV file may not exceed the file size of
5 MB
!
