manualshive.com logo in svg

Comba Telecom RA-7800, Installation Manual

Share
Download
Comba Telecom RA-7800 Installation Manual Download Page 36

INSTALLATION GUIDE FOR RA-7800 

 

RA-7800 QI  

Copyright - refer to title page 

Page 36

ENU Status : 1-0-1 

 

 

The following are the introduction on the connectors of each FOU type.    
 

Single Channel FOU 

without WDM  

 

This is applicable when no integrated WDM is required. It implements 
the connection between MU and RU through dual fiber. Each single 
channel FOU can serve one RU. 

OP/Downlink 

FC/APC connector for downlink optical output port. 
It is connected to the “OP/Downlink” port of RU. 

FOU 

OP/Downlink

OP/Uplink

 

OP/Uplink 

FC/APC connector for uplink optical input port. It is 
connected to the “OP/Uplink” port of RU. 

Table 11: Single Channel FOU SIU description 

 
 

Single Channel FOU  

with WDM 

WDM unit integrated to implement the connection between MU and 
RU through single fiber. Each Single Channel FOU with WDM can 
serve one RU. (standard application) 

 

FOU 

OP/DL_UL

 

OP/DL_UL 

FC/APC connector for optical input/output port. It is 
connected to the “OP DL_UL” port of RU. 

Table 12: Single Channel FOU SIU with WDM description 

 
 
 
 
 
 
 
 
 

 

Summary of Contents for RA-7800



























































Reviews:

No comments

Brands by name

Popular brands

Load more brands