background image

SAFETY REQUIREMENTS FOR E.DO GRIPPER USE

7

Comau Robotics Product Instruction

Remove the e.DO Gripper from the related packaging, proceeding as indicated below:

The e.DO Gripper is packed in a normal cardboard box with pressure lock; no 
special tools are required to remove the packaging;

remove the packaging paying particular attention not to damage the contents;

make sure that all the components indicated in the previous 

Fig. 1.2

 are present 

inside the package;

after removing the packaging, make sure the e.DO Gripper does not show signs of 
damage during transport; if it does, do not install e.DO Gripper and contact the 
Comau Service Centre (see the following address: 
edo.cloud/support-and-contacts/);

the packaging materials must be kept out of reach of children, as they are potential 
sources of danger.

1.2.2

Preliminary requirements and instructions for installation

Before proceeding with the installation of e.DO Gripper:

check that the e.DO Robot is powered off, that the related main switch is open (0 - 
OFF position) and that the power supply cable is disconnected;

The e.DO Gripper is designed and built to be used exclusively in indoor domestic 
/ scholastic environments and protected from atmospheric agents. It is not 
intended for use in industrial or in hazardous environments (e.g. environments with 
potential risks of explosion).

The e.DO Gripper can be used for the execution of programs including small 
operations for handling small and non-dangerous objects, compatibly with the 

General technical features

 of the e.DO Gripper and of the e.DO Robot. Depending 

on the nature and features of the handled items (configuration, weight, etc.), after 
the evaluation performed by the User there can be needed the installation of 
perimeter protective guards, that prevent the reaching of the Robot by the 
surrounding people, and an additional emergency push-button outside the guards 
themselves (see 

par. 3.4

);

carry out the e.DO Gripper installation as indicated in the 

e.DO Gripper installation 

procedure

.

Do not handle the e.DO Gripper and perform the installation working with wet or damp 
hands or feet.

Summary of Contents for e.DO





























Reviews: