12.4. Electronic motor alignment
The display panel of the
iWash Halo
allows for the electronic alignment of the projector’s motors in the optical system. This procedure
is performed by
Coemar
at the factory. It may be useful to perform this procedure in the case of internal components being replaced.
Altering the factory settings may radically alter the functioning of the projector. Carefully read all of the following prior to attempting any
changes.
Electronic calibration
1.
Press the
menu
button and then
enter
to confirm.
2.
Press the
+
or
-
button until
FUNC
is displayed. Then press
enter.
3.
Press the
+
or
-
button until
RESE
is displayed.
4.
Press the
enter
and
menu
buttons simultaneously, holding them for at least
10"
. The motors will perform a reset and the display will show
-- -- -- --
for a few seconds. After this, the display will show
PAN
confirming that you have entered electronic calibration mode.
Note:
Simultaneously pressing the
+
and
-
buttons will return the calibration value to 128 (default).
All the components of the
iWash Halo
are available as replacement spares from your authorisded
Coemar
service centre. Accurate
description of the fixture, model number, and type will assist us in providing for your requirements in an efficient and effective manner.
13. Spare parts
RESE
AOO1
☞
+
o
--
FUNC
☞
+
o
--
☞
menu
PAN
pan alignment
Pan movement alignment
TILT
tilt alignment
Tilt movement alignment
SH UT
shutter alignment
Shutter movement alignment
D I M M
dimmer alignment
Dimmer level alignment
EFF
effect wheel alignment
Effect alignment
COLR
colour wheel alignment
colour wheel alignment
CYAN
cyan
Cyan filter alignment
MAGE
magenta
Magenta filter alignment
YELL
yellow
Yellow filter alignment
ZOOM
zoom
Zoom lens alignment
CTB
CTB
CTB filter alignment
LAMP
lamp power level
Lamp power level setting
END
end
To end the electronic setting procedure and
confirm therecording.
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
+
o
–
☞
+
o
–
☞
enter
0000
☞
enter
☞
+
o
–
es.
0 1 4 0
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 3 0
☞
+
o
–
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 5
☞
+
o
–
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 3 5
☞
+
o
–
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 3 2
☞
+
o
–
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 1
☞
+
o
–
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
+
o
–
☞
enter
0 1 2 8
☞
enter
☞
+
o
–
es.
0 1 2 0
☞
+
o
–
☞
enter
☞
+
o
–
es.
0 1 2 7
0 1 2 8
☞
enter
A001
☞
+
o
–
☞
enter
☞
enter
LEV.0
☞
enter
☞
+
o
–
es.
LEV.3
☞
+
o
–
☞
enter
0128
☞
enter
☞
+
o
–
es.
0 1 2 1
☞
+
o
–
Press together
enter
and
menu
keys
for 10 seconds: the display will show
alignement functions menu
ATTENTION!!
The alignment procedure can only be carried out when DMX 512 signal is connected.
ATTENTION!!
This procedure should only be undertaken by qualified and experienced technical personnel..
20
English
