COBHAM 7023A Installation Manual Download Page 152

Page: 152 / 167

98-175666-A

Appendix F: Event messages

F-10

List of events

0A107-0 Antenna ERROR

ISCM Power good

Internal PSU error.

0A108-0 Antenna ERROR

ISCM Prod data

Internal production data invalid.

0A180-0 Antenna WARNING ISCM Fan error

BUC fan failure. Check fan movement.

0A181-0 Antenna ERROR

ISCM No response

No communication with ISCM. Check cable.

0A200-0 Antenna ERROR

Azi Motor prod data Internal production data invalid.

0A201-0 Antenna ERROR

Azi Motor ZRM

No zero reference found. Check from motor to ZRM
and free movement of the antenna.

0A280-0 Antenna ERROR

Azi Motor Driver fault Driver could not move antenna. Check free

movement of the antenna.

0A281-0 Antenna ERROR

Azi Motor Power fault No power to motor driver. Check input power to

system.

0A282-0 Antenna ERROR

Azi Motor Shutdown Internal error. Motor is shut down.

0A283-0 Antenna ERROR

Azi Motor Over
temperature warning

Motor temperature too high.

0A284-0 Antenna ERROR

Azi Motor Over
temperature fault

Motor temperature too high. Motor shut down.

0A285-0 Antenna ERROR

Azi Motor Over
current fault

Over current protected activated. Check free
movement of antenna.

0A286-0 Antenna ERROR

Azi Motor No
response

No communication with motor. Check cable.

0A300-0 Antenna ERROR

Xel Motor prod data

Internal production data invalid.

0A301-0 Antenna ERROR

Xel Motor ZRM

No zero reference found. Check from motor to ZRM
and free movement of the antenna.

0A380-0 Antenna ERROR

Xel Motor Driver fault Driver could not move antenna. Check free

movement of the antenna.

0A381-0 Antenna ERROR

Xel Motor Power fault No power to motor driver. Check input power to

system.

0A382-0 Antenna ERROR

Xel Motor Shutdown Internal error. Motor is shut down.

0A383-0 Antenna ERROR

Xel Motor Over
temperature warning

Motor temperature too high.

0A384-0 Antenna ERROR

Xel Motor Over
temperature fault

Motor temperature too high. Motor shut down.

0A385-0 Antenna ERROR

Xel Motor Over
current fault

Over current protected activated. Check free
movement of antenna.

0A386-0 Antenna ERROR

Xel Motor No
response

No communication with motor. Check cable.

0A400-0 Antenna ERROR

Ele Motor prod data

Internal production data invalid.

Module Type

Description

Explanation

Table F-1: Event messages (Continued)

Summary of Contents for 7023A








































































































































































Search results

Summary of Contents for 7023A

Reviews:

Related manuals for 7023A

Brands by name

Popular brands

COBHAM 7023A, Installation Manual

Search results

Summary of Contents for 7023A

Reviews:

Related manuals for 7023A

Brands by name

Popular brands