manualshive.com logo in svg

CME BodyGuard 121 Twins, Operator'S Manual, Page: 49 / 81

Share
Download
CME BodyGuard 121 Twins Operator'S Manual Download Page 49

4-Operation 

– Intermittent Infusion  

 

 

 

 

49

 

 

NOTE:

 

If pump is in 

Delay Mode

, enter Start Time (24 Hour Clock) and Start Date. For further 

information regarding the Delay Option, refer to Delay Program section. 

9. 

Press 

 to Start Infusion. Delay time option is 

disablde, screen will show start time as “Immediate”. 

 

 

 

10. 

During  program  operation,  the  pump  displays  the  rate  in 

which the program is operating.   

 

 

 

 
 

 

NOTE:

 

If one of the values is changed during the programming mode, the pump will not recall 

the new value unless changes are confirmed by pressing 

.          

 

 NOTE

:  If  prime  procedure  is  activated  during  data  setting, the  pump  will  return  to the  original 

(previous) screen once priming has completed. 

 

 

NOTE:

 

Whenever required to stop infusion, press 

. Stop displays on the screen. Stop 

mode  is  limited  to  two  minutes.  After  two  minutes  an  audible  alarm  sounds.  Press                

 again to mute the alarm or press STOP/NO until the pump powers off.

   

 

 
Rate Adjustment 

 

It is necessary to stop infusion in order to change any or all parameters of the current infusion program 

 

To change the rate while in Stop mode: 

 

1. 

Press any number on the keypad and then press 

. 

2. 

Adjust the rate and press 

. 

3. 

Adjust all other parameters and press 

 to restart infusion. 

 

Next 

Dose 

Start 

Time: 

 

Immediate 

Press OK to start 

Rate

 

                

25 

ml/h

 

 

Summary of Contents for BodyGuard 121 Twins


















































































Reviews:

No comments