manualshive.com logo in svg

CME BodyGuard 121 Twins, Operator'S Manual, Page: 25 / 81

Share
Download
CME BodyGuard 121 Twins Operator'S Manual Download Page 25

 

 

 

 

25

 

 

The pump display will show the accumulation screen where 

all  set  data  is  shown,  check  the  setting,  if  correct,  press 

  to start operation.  

  

 

           

7. 

Wait untill pump displays the 

“low battery” message 

 

 

8. 

Press  

   to turn the pump off.  

9. 

Connect the pump to a charger. 

10. 

Verify that the red LED indicating an empty battery lights on (lower left side of the charger above 

channel one). 

11. 

Verify that the full battery LED lights red after 4-6 hours of charging (upper left side of the charger 

above channel one). 

 
Charger Indicator Test 

 

1. 

Click  the  pump  into  the  charger  and  connect  the  charger  to  mains.  Disconnect  the  power  cord 

from the AC power outlet. 

2. 

Verify that the CHARGE LED indicator (in the charger right side above channel II) is off.  

3. 

Connect the power cord to the AC power outlet. Verify that the CHARGE LED indicator is on. 

 

 

 

 

 

 
Administration Sets 

 

The 

BodyGuard 121 Twins

 infusion System should only be operated with Infusion sets approved for use 

by the manufacturer and distributor.  

 

 

 

Warning:

 

Do  not  operate  the 

BodyGuard  121  Twins

  Infusion  system  with  any 

administration  set,  other  than  that  recommended  by  the  manufacturer  or  its  distributor.  The 

optional 

BodySet/MicroSet

  Infusion  Sets  are  equipped  with  a  free  flow  protection  valve,  to 

prevent  a  gravitational  free  flow  hazard.  Using  a  different  set  may  essentially  change  the 

administration rate and expose the patient to free-flow.

 

 

 
 

   Low Battery 

 

  Connect To Charger

 

Rate                       500 ml/h

 

Volume left             20 ml

 

Infused                       0  ml

 

Press Ok to Start

 

Summary of Contents for BodyGuard 121 Twins


















































































Reviews:

No comments