background image

APOLLO 60 HP SUPPLIED-AIR RESPIRATOR

x

04440

Flow Regulator

x

04410

Flow Regulator

x

04411

Flow Regulator

x

21422

Cont. Flow Conn.

x

04397

Hose 25 Ft.

x

04415

Hose 50 Ft.

x

04398

Hose 100 Ft.

Page 1

Clemco Industries Corp.

Washington, Missouri USA

(314) 239-0300

TYPE C AND CE CONTINUOUS FLOW SUPPLIED-AIR RESPIRATOR IS APPROVED

ONLY IN THE FOLLOWING CONFIGURATIONS:

TC#

19C-130

APL

SA

1 PROTECTION

SA-Supplied -air

2  CAUTIONS AND LIMITATIONS

B- Not for use in atmospheres immediately dangerous to life or

health.

C-Do not exceed maximum use concentrations established by

regulatory standards.

D-Air-line respirators can be used only when the respirators are

supplied with respirable air meeting the requirements of
CGA G-7.1 Grade D or higher quality.

E- Use only the pressure ranges and hose lengths specified

in the user's instructions.

J- Failure to properly use and maintain this product could

result in injury or death.

M-All approved respirators shall be selected, fitted, used, and

maintained in accordance with MSHA, OSHA, and other
applicable regulations.

N-Never substitute, modify, add, or omit parts.  Use only exact

replacement parts in the configuration as specified by the
manufacturer.

O-Refer to users instructions, and/or maintenance manuals for

information on use and maintenance of these respirators.

S-Special or critical users instructions, and/or specific use

limitations apply.  Refer to instruction manual before donning.

B C D E J N O S

MODEL

PROTECTION 

1

Cautions and

Limitations 

2

Components

Alternates

1.0

INTRODUCTION

1.1

Scope of manual

1.1.1

This manual covers setup, operation, mainte-

nance, replacement parts, and important warnings for safe
operation of the Clemco Apollo 60 HP Supplied-Air Respi-
rator.

1.1.2

OSHA requires the employer to establish a com-

prehensive respiratory protection program per regulations
29 CFR 1910.134(a)(b) and 29 CFR 1926.103, to include
the following:

1.

Program coordination by a designated

responsible individual.

2.

Evaluation of each worker’s ability to perform

the work while wearing a respirator.

3.

Periodic training.

4.

Periodic environmental monitoring.

5.

Respirator-fit testing.

6.

Maintenance, inspection cleaning, and

storage of the respirators.

7.

Selection of the proper NIOSH-approved

respirator.

1.1.3

For safe use of the respirator, it is essential that

the user be properly instructed in its use and maintenance.
This manual must be made available to all users of the
respirator. [Reference OSHA Regulations 1910.134.]  Read
the entire manual before installing or operating the equip-
ment.

1.1.4

The respirator must be supplied with respirable air

meeting requirements described herein. It is the responsi-
bility of the owner to provide quality breathing-air to the
respirator, and to establish a program to ensure that the
respirator is properly used and maintained.

1.1.5

The following manuals are available for accesso-

ries that may be used in conjunction with the Apollo
Respirator.

Description

Manual No.

CAT Cool-Air Tube

08956

CCT Climate Control Tube

08850

CPF Particulate Air Filter

04143

ABL 4021 CarbonMonoxide Alarm

21457

1.2

Hazard Alerts

1.2.1

Clemco uses signal words, based on ANSI Z535.2-

1991, to alert the user of a potentially hazardous situation
that may be encountered while operating this equipment.
ANSI’s definitions of the signal words are as follows:

! NOTICE

“Notice” is used to indicate a statement of com-
pany policy as the message relates directly or
indirectly to the safety of personnel or protection
of property.

! CAUTION

“Caution” is used to indicate a potentially hazard-
ous situation which, if not avoided, may result in
minor or moderate injury.

x

10506

Helmet

Summary of Contents for Apollo 60 HP















Reviews: