background image

 

APOLLO LOW PRESSURE SUPPLIED-AIR RESPIRATOR 

Page 14 

HELMET MODEL 20 

 

 

 

 

 

© 2011 CLEMCO INDUSTRIES CORP.  

  

www.clemcoindustries.com

  

  Manual No. 21991

 

9.6.2.9

 Make sure the chin strap is in place, then 

reattach the cape to the helmet by following the 
instructions in Section 9.5. 

 
 
9.7 Chin 

Strap 

 

9.7.1 

Replace the chin strap when worn or when it 

loses its elasticity. 

 
 
9.8 

Removing and Replacing the Air Channel 

Partition 

 

9.8.1

 

Remove the cape and suspension per Sections 

9.5 and 9.6. 
 

9.8.2 

Pull the partition from the front to unsnap it from 

the retainers. Remove the back end of the partition from 
the tabs. 
 

9.8.3 

Place a new partition into the hood; insert the 

slots on the back end of the partition behind the tabs. 
 

9.8.4

  While applying pressure on the front of the 

partition, work from the back toward the front and snap it 
into place. 
 

9.8.5 

Replace the suspension and cape. 

 

 
 

10.0 REPLACEMENT 

PARTS 

 

 

WARNING 

Use of any non-Clemco replacements parts may 
permit ingress of hazardous contaminants, and 
may cause injury, disease, or death to the user. 
OSHA Regulation 29 CFR 1910.134(H)(4)(i) 
requires the use of the respirator 
manufacturer’s NIOSH-approved parts 
designated for the respirator. Using any parts 
listed in this section made by any manufacturer 
other than Clemco voids the NIOSH approval, 
and voids Clemco’s warranty. 

 
 
10.1 

Supplied-Air Respirator Systems and 

 Alternate 

Accessories 

 

Respirator Systems 

 

Description Stock 

No. 

 

Apollo 20 LP

 

Supplied-Air Respirator with Standard 

DLX Padded Suspension 

 

less respirator hose........................................... 25292 
with 50-foot respirator hose .............................. 25293 

 
 

Accessories 

 

Description Stock 

No. 

 

Constant-flow connector, LP with belt  .................... 21777 

 

Pressure conversion kit, LP to HP 

Converts Apollo 20 LP, low pressure 
(ambient air) respirator to high pressure  
(Grade “D” Compressed Air) respirator ................ 22690 

 

DLX padded suspension kit 

Includes everything needed to replace padded 
suspension, or to convert from web suspension 
to DLX padded suspension  ............................... 25215 

 

Hearing protection muffs,  
  Low profile noise reduction muffs  
  for use with web suspension w/sweatband only. 
  May not work with all head sizes  ....................... 23886 

 

Do-rag, washable head scarf  ................................. 23814 

 

CMS-3 CO monitor package ................................... 24612 
 

Summary of Contents for APOLLO 20





















Reviews: