background image

APOLLO SUPPLIED-AIR RESPIRATOR 

Helmet Model 20 

Low Pressure 6 psi to 20 psi 

O. M. 21991 

 

 

 

 

Do not proceed with 
these instructions until 
you have READ the 
orange cover of this 
MANUAL and YOU 
UNDERSTAND its 
contents. *  
These WARNINGS are 
included for the health 
and safety of the 
operator and those in 
the immediate vicinity.

  

 

*If you are using a Clemco Distributor 
Maintenance and Part Guide, refer to 
the orange warnings insert preceding 
the Index before continuing with the 
enclosed instructions.  

 

Electronic files include a Preface 
containing the same important 
information as the orange cover.

 

 

© 2011 CLEMCO INDUSTRIES CORP.

One Cable Car Dr. 

Washington, MO 63090 

Phone (636) 239-4300 

F

ax

 

(800)

 

726-7559 

Email: [email protected] 

www.clemcoindustries.com

 

 

 

WARNING

NOTICE 

This supplied air respirator conforms to all 
NIOSH specifications and standards and carries 
NIOSH approval. As manufactured, this 
respirator complies only with those foreign 
approvals that accept NIOSH certification. 
Specifically, it has not been manufactured to 
European

 standards and does not carry the 

European 

 mark. 

MC FILE NUMBER:  1193-0196 
DATE OF ISSUE: 

April, 1996 

REVISION: H, 

01/11 

Summary of Contents for APOLLO 20





















Reviews: