ClearSpan 106772 Manual Download Page 9

Page: 9 / 53

CLEARSPAN

™

JOB MASTER BUILDINGS

Revision date: 07.23.09

MAIN FRAME RAFTER ASSEMBLY (CONTINUED)

MAIN FRAME END RAFTERS

Complete the following steps to assemble the two (2) end

rafters for the main frame.

NOTE:

The two (2) end rafters are assembled using 3-Way

square tube fittings (#104626) positioned between the

upper tube splices.
1. Select the tubes needed to assemble the rafter and

place these on the ground as shown on previous page.

NOTE:

The lower leg pipes (#S20P036) are 36" long.

The upper (#S20P048) pipes are 48" long.

Measure the

pipes if needed to install them in the correct location.

DO NOT USE THE 46" (S20P046) SQUARE TUBES;

THEY ARE RESERVED FOR THE PURLINS OF THE

MAIN FRAME.

2. Insert the 3-Way square tube fittings (#104626) into the

rafter pipes as shown below and secure them using Tek

screws.

The free end of each 3-Way square tube fitting

(#104626)

must face the same direction.

The free

section of the tube fitting is used to connect the purlin

pipes.

With the rafter on the ground, the free end of the

fitting will point straight up.

IMPORTANT:

To prevent damage to the main cover,

position the Tek screws so the heads do not contact the

main cover when it is installed.

3. Connect the lower rafter legs using the 1.75" x 1.75"

square tube insert (#104075). (See the Base Rail

assembly steps if needed.) Place the insert 8" into the

rafter pipes and secure using Tek screws.

4. Repeat Steps 1–3 for the remaining end rafter.

NOTE:

There are only two (2) end rafter assemblies.

MAIN FRAME INTERIOR RAFTERS
1. Select the tubing for the first interior rafter assembly

and position it on the ground as previously described

for the end rafters.

2. Install a 4-Way square tube fitting (#104627) in the

locations shown in the diagram below and secure the

joints using Tek screws.

With the rafter on the ground,

one free end of each

4-Way tube fitting will point up; the other free end will

point toward the ground.

IMPORTANT:

To prevent damage to the main cover,

install Tek screws so the heads do not contact the main

cover when it is installed.

3. Repeat the steps for all remaining interior rafters.
4. Once all rafter assemblies are complete, continue with

the MAIN FRAME ASSEMBLY instructions that follow.

Summary of Contents for 106772






















































Search results

Summary of Contents for 106772

Reviews:

Brands by name

Popular brands

ClearSpan 106772, Manual

Search results

Summary of Contents for 106772

Reviews:

Brands by name

Popular brands