manualshive.com logo in svg

ClearSpan 106772, Manual

Share
Download
ClearSpan 106772 Manual Download Page 25

CLEARSPAN

™

 JOB MASTER BUILDINGS

25

Revision date: 07.23.09

14. Measure the opening along the frame to determine the 

required width for the final row of panels.

ATTACH OUTRIGGER PANELS (CONTINUED)

15. Select a panel and mark the dimension on the panel.  

 

NOTE:

 Measure from the edge of the panel that has 

the rib with the anti-siphon groove. 

Do not remove the 

rib with anti-siphon groove. 

This rib is placed under 

the rib of the previous panel to complete the panel 

installation for the side.

16. Cut the panel to the required width. 

 

PANELS ARE SHARP. HANDLE WITH GLOVES AND 

USE CAUTION WHEN CUTTING THE PANEL!

17. Slide the upper edge of the panel under the previous 

panel and secure it to the frame.  

ATTENTION: 

Attach the lower panel edge of all panels 

in this row to the base rail using Tek screws and neo-

bonded washers spaced evenly along the rail.

18. Continue preparing and attaching panels to complete 

the last row for this outrigger frame.

19. Repeat the procedure to install the metal panels for the 

remaining outrigger frame.

20. After the panels are installed on the outrigger frames, 

continue by attaching the panels to the rafters of 

the main frame. 

Install these panels using the same 

method of overlapping described above.

 

After installing all outrigger 

roof and end panels, attach 

the panels to the inside of 

the main frame.

NOTE:

 The frame diagram above shows the metal 

panels attached to the inside of the main frame of the 

building. Information describing how to install these 

panels is presented in the next procedure.

Insert shows a power tool used to 

cut a panel to the required width. 

Use a similar tool to when cutting 

metal panels.

Cut and slide last row 

of panels into place.

Space below is reserved for customer notes.

Summary of Contents for 106772






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands