manualshive.com logo in svg

ClearSpan 106772, Manual

Share
Download
ClearSpan 106772 Manual Download Page 15

CLEARSPAN

™

 JOB MASTER BUILDINGS

15

Revision date: 07.23.09

OUTRIGGER FRAME ASSEMBLY (CONTINUED)

9.  Secure the second rafter to the 1-Way connector on 

the outrigger base rail and adjust the rafter width as 

needed to achieve the 48" on-center dimension. 

 

NOTE:

 The end of the purlin at the end rafter extends 

about 1/2" through the pipe strap as shown below. 

 

To prevent conflicts with the installation of the end wall 

metal panels, do not allow the purlin pipe to extend 

beyond the edge of the rafter. 

Diagram A (above) shows pipe strap and purlin at the 

first rafter. Diagram B (below) shows the purlin at the 

second (or inside) rafter. (Pulin position may vary.)

10. With the purlin in position, secure the pipe strap to the 

first rafter and install a Tek screw through the pipe strap 

and into the purlin. See Diagram A.

11.  Verify that the rafter spacing is 48" on-center, tighten 

the pipe strap on the second rafter, and install a Tek 

screw through the pipe strap to secure the purlin in the 

strap.

12. Repeat the above steps as needed to attach the 

remaining outrigger rafters to the main frame and to 

complete the installation of the purlin for the first side. 

 

Tek screw

Tek screw

NOTE:

 End the purlin run with the 

shorter,

 

plain pipe

 

(131P0XX), where the XX represents the length 

needed to reach the end of the frame. This pipe does 

not have a swaged/tapered end. If the end rafter is 

plumb and the purlin extends beyond the pipe strap 

when installed, cut the purlin pipe as needed to keep it 

from extending past the end rafter. 

 

Typically purlin pipe does not need to be cut. 

Verify that 

you have selected the correct pipe before cutting a pipe 

to length.

13. Return to each pipe strap and verify that all Tek screws 

are tight and that a Tek screw has been installed to 

secure the purlin to the pipe strap.

14. Return to each purlin pipe splice and secure the splice 

with a Tek screw as shown below. 

ATTENTION:

 All pipe splices are secured with Tek 

screws.

15. Verify that all Tek screws are installed and tight and 

that all fasteners used to secure the frame to the main 

frame assembly are properly installed and tight.

16. After the assembly and installation of the first outrigger 

frame is complete, repeat the steps to assemble and 

install the remaining outrigger frame. 

17. Continue by installing the diagonal braces for the main 

frame rafters as described in the following procedure.

Diagram A

End Rafter

Diagram B

Inside 

Rafter

Summary of Contents for 106772






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands