ClearSpan 106772 Manual Download Page 51

Page: 51 / 53

CLEARSPAN

™

JOB MASTER BUILDINGS

Revision date: 07.23.09

PANEL INSTALLATION DIAGRAMS

These diagrams show where to install the different size

roof panels for

each frame length for one row

. (Each

row uses panels of the same length.) Locate your

building below and install the panels using the diagram

as a guide.

All roof panels are shipped in two (2) different lengths:
• 8' 2" (98")
• 12' 2" (146")

ATTENTION:

Do not cut roof panels.

All roof panels are

installed as shipped. Panels are designed to overlap

each other. For superior sealing, apply a bead of

sealant a few inches in from the edge on the panel that

is overlapped by next panel during the installation.

Sealant is supplied by the customer.

SKU: #106772: 20'

One 98" panel and one 146" panel

SKU: #106773: 24'

Two 146" panels

SKU: #106774: 28'

Two 98" panels and one 146" panel

Summary of Contents for 106772






















































Search results

Summary of Contents for 106772

Reviews:

Brands by name

Popular brands

ClearSpan 106772, Manual

Search results

Summary of Contents for 106772

Reviews:

Brands by name

Popular brands