manualshive.com logo in svg

ClearSpan 106772, Manual

Share
Download
ClearSpan 106772 Manual Download Page 8

CLEARSPAN

™

 JOB MASTER BUILDINGS

8

Revision date: 07.23.09

ASSEMBLE AND POSITION MAIN FRAME BASE RAILS 

(CONTINUED)

ATTACH 104624 FITTINGS (RAFTER FEET)

 

Gather the parts:
•  Assembled base rails
•  1-Way square tube fittings (#104624)
•  Tek screws and magnetic nut setter (3/8'' x 2-9/16")
•  Tape measure and marker 

NOTE:

 Before attaching the 104624 fittings, position 

the base rail so the heads of the Tek screws face to the 

outside, which will be toward the outrigger frame when 

these are installed. 

Do not position the rail with the Tek 

screws on the top, bottom, or inside of the rails. Doing so 

may interfere with the installation of the #104624 fittings 

and metal panels.

1.  Using Tek screws, attach the first square tube fitting  

(#104624) to the top of the base rail flush with the end 

of the base rail as shown.

2.  From the center of the installed square tube fitting  

(#104624), measure and mark 48" increments along 

the length of the base rail. These marks represent the 

4' on-center rafter positions.

3.  Center a square tube fitting (#104624) on each mark 

and secure the fitting to the base rail using Tek screws.

4.  Repeat the steps for the remaining base rail. 

NOTE:

 Rafter spacing is measured center-to-center.

5.  Position base rails on the site where the shelter will be 

assembled. Space rails at the approximate width of the 

shelter. 

 

ATTENTION:

 Do not anchor the rails to the site at this 

time.

6.  After the base rails are assembled, continue with the 

MAIN FRAME RAFTER ASSEMBLY.

48" 

center-to-center

#104624 

Square Tube 

Fitting

Center of the fitting

Tek screws

MAIN FRAME RAFTER ASSEMBLY 

Gather the parts:
•  Rafter pipe ( #12CP20P1) 
•  Rafter pipe (#18CP20P3)
•  Rafter pipe (#S20P036 & #S20P048)
•  3-Way Square tube fittings (#104626)
•  4-Way Square tube fittings (#104627)
•  Tek screws and magnetic nut setter (3/8'' x 2-9/16")

Main Frame Rafter Assembly Procedure

 

Each rafter assembly consists of seven (7) rafter tubes: one 

(1) curved center pipe (for the top or peak), two (2) bent leg 

pipes, two (2) straight pipes between the peak and the bent 

leg pipes, and two (2) straight pipes. 

 

NOTE:

 The different end rafter tubes are connected using 

3-Way tube fittings (upper rafter) and square tube insert 

(#104075) for the rafter legs (lower).

Interior or mid rafters use 4-Way tube fittings in place of

the 3-Way tube fittings used for the end rafters.

#18CP20P3

#12CP20P1

#S20P036

#S20P048

Summary of Contents for 106772






















































Reviews:

No comments

Brands by name

Popular brands

Load more brands