manualshive.com logo in svg

Claydon HYBRID T4, Operator'S Manual, Page: 43 / 56

Share
Download
Claydon HYBRID T4 Operator'S Manual Download Page 43

43 

CLAYDON TRAILED 4 METRE

 

Hybrid Seed Drill

L.3.SR

Seed level right is low 

(Seed only drill with 2 
metering units, independent 
left & right level sensors)

•  Seed level right is actually low
•  Sensor is functioning correctly

•  Wiring between sensor and 

connection box is correct

•  Wiring between connection box 

and CAN module is correct

L.3.SD

Both seed levels are low

(Seed only drill with 2 

metering units, independent 

left & right level sensors)

•  Seed levels are actually low

•  Sensors are functioning correctly

•  Wiring between sensors and 

connection box is correct

•  Wiring between connection box 

and CAN module is correct

L.3.FD

Fert level is low

(only Seed & Fert drill, 2 

metering units per product)

•  Fert level is actually low
•  Sensor is functioning correctly

•  Wiring between sensor and 

connection box is correct

•  Wiring between connection box 

and CAN module is correct

L.4.L

Half Width Enabled –
Left Side

(only Seed drill, 2 metering 
units per product

)

•  Left side motor is disabled due 

to pressing the on-screen motor 

inhibit button.

•  Re-press to re-enable the motor or 

ignore to continue with half width 

drilling.

L.4.R

Half Width Enabled –
Right Side

(only Seed drill, 2 metering 

units per product)

•  Right side motor is disabled due 

to pressing the on-screen motor 

inhibit button.

•  Re-press to re-enable the motor or 

ignore to continue with half width 

drilling.

L.5.S

Single Motor Metering 

Off

•  Motor is disabled due to pressing 

the on-screen motor inhibit 

button.

•  Re-press to re-enable the motor or 

ignore to continue with the motor 

inhibited.

Summary of Contents for HYBRID T4

























































Reviews:

No comments