background image

2

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

INTRODUCTION

Thank you for purchasing this CLARKE Cement Mixer.

Before attempting to use this product, please read this manual thoroughly and 
follow the instructions carefully. In doing so you will ensure the safety of yourself 
and that of others around you, and you can look forward to your purchase 
giving you long and satisfactory service.

SPECIFICATION

GENERAL SAFETY PRECAUTIONS

1.

ALWAYS

 keep the work area clean and well lit. Floors should always be kept 

clear. Cluttered or dark areas invite accidents.

2.

ALWAYS

 keep children and bystanders away while operating this machine. 

Distractions can cause loss of control.

3.

ALWAYS

 stay alert & do not use a machine while you are tired or under the 

influence of medication or alcohol.

4.

ALWAYS

 wear suitable protective clothing and eye protection including 

industrial gloves, ear defenders & approved impact resistant safety glasses. 
(Eye glasses are NOT safety glasses). Wear a dust mask if handling cement.

5.

NEVER 

over-reach. Keep your proper footing and balance at all times to 

enable better control of the machine in unexpected situations.

Max drum capacity

125 Litre

Max mixing capacity

79 Litre

Drum speed

26.6 rpm

Duty cycle classification

S6 30%

Drum turning axis

360

o

Weight

45 kg

Dimensions: Length x Width x Height

1180 x 705 x 1070 mm

Power cable length

1.5 m

IP rating

IP44D

Sound power guaranteed

91 dB LWA

Summary of Contents for 3400841

















Reviews: