background image

3

Parts & Service: 020 8988 7400 / E-mail: [email protected] or [email protected]

6.

NEVER

 stand on the machine. Injury could occur from a fall.

7.

ALWAYS

 store machines out of reach of children.

8.

ALWAYS

 read and become familiar with the entire operating manual.

9.

NEVER

 allow persons unfamiliar with this manual to operate this machine.

10.

ALWAYS

 maintain the machine with care and keep it clean for best / safest 

performance.

11.

NEVER

 use this machine if any part is damaged. Have it inspected and 

repaired by a competent technician.

12.

NEVER

 modify this machine in any way. Use it only for the purpose for which 

it is designed.

13.

ALWAYS

 ensure the electrical cable is fully protected and there is no 

danger of damage from equipment or materials. Always Inspect the cable 
before use and replace if any damage is apparent.

14.

ALWAYS 

avoid inhaling cement dust while loading the mixer. Avoid contact 

with cement or any mixing additives being used. Wear gloves/face mask if 
necessary.

15.

ALWAYS

 disconnect the machine from the power supply when not in use, 

and before carrying out any maintenance.

16.

NEVER 

leave the machine running unattended or leave the machine until it 

comes to a complete stop.

17.

ALWAYS 

keep your hands well clear of the rotating drum at all times. Never 

put your hands inside the drum when the machine is switched on.

18.

NEVER

 put any tools or other objects in or around the drum while it is 

rotating.

19.

NEVER

 wear jewellery or loose clothing that could be snagged by any part 

of the rotating drum.

20.

NEVER

 load the drum when the machine is switched off. Always switch on 

and ensure the drum is rotating before loading.

21.

NEVER 

operate this machine on a gradient. Always stand the mixer on firm, 

level ground where it cannot tip over.

22.

ALWAYS

 switch off and disconnect from the power supply before moving 

the machine around the work site.

23.

NEVER

 use the mixer if the power cable or other important parts of the 

machine are damaged.

24. If an extension cable is used, the cable and plug must be of watertight 

construction. Inadequate extension cables can be dangerous.

Summary of Contents for 3400841

















Reviews: